Biostar

How can you to fix the problem?
This is because Microsoft Windows 7 which not bundle it, so you can try to install the Microsoft HotFix KB3020369 and KB3125574 before install onboard Chipset and Graphics drivers.
Of course, if the action still not to fix, please try to run Windows 7 online Update to latest version.

Please ensure your board connect to network, first

<< Step.1   Install Windows Hotfix -  KB3020369 >>

KB3020369 x64 ==> For Windows 7 64bit OS
http://download.windowsupdate.com/d/msdownload/update/software/updt/2015/04/windows6.1-kb3020369-x64_5393066469758e619f21731fc31ff2d109595445.msu 
KB3020369 x86 ==>  For Windows 7 32bit OS
http://download.windowsupdate.com/d/msdownload/update/software/updt/2015/04/windows6.1-kb3020369-x86_82e168117c23f7c479a97ee96c82af788d07452e.msu 

<< Step.2   Install Windows Hotfix - KB3125574 >>

KB3125574 x64 ==> For Windows 7 64bit OS
http://download.windowsupdate.com/d/msdownload/update/software/updt/2016/05/windows6.1-kb3125574-v4-x64_2dafb1d203c8964239af3048b5dd4b1264cd93b9.msu 
KB3125574 x86 ==> For Windows 7 32bit OS
http://download.windowsupdate.com/d/msdownload/update/software/updt/2016/05/windows6.1-kb3125574-v4-x86_ba1ff5537312561795cc04db0b02fbb0a74b2cbd.msu 

<< Step.3  Run Windows 7 online update >>
If these hot fix still not to fix, please try to run Windows 7 online Update to latest version. 

<< Step.4  Install Chipset driver and graphic driver again >>
After that, then you will start to install onboard chipset and graphics driver.

Last, both of yellow Exclamation marks (AMD PSP 2.0 Device & AMD High Definition Audio Device) will disappears after follow above 4 method.

How to make RAID 0 array to install Windows 10 64 bit for TB350-BTC motherboard with two SATA HDD?

1. Press [Delete] key in POST screen go to BIOS > Advanced > SATA Configuration > OnChip SATA Type, set it to [RAID] mode.

2. Press [F10] key to Save Configuration and reset.

3. Press [Ctrl] + [R] to configure.

4. Choose "Delete Array(s)" press [INS] to select arrays and press [Enter] to delete all.

5. Press [C] to continue.

6. Choose Create Array.

7. Press [INS] to select Disks and press [Enter].

8. Press [Enter] to select RAID0.

9. Press [Enter] to Complete.

10. Select "Read / Write".

11. Press [C] to Confirm.

12. Choose Continue to Boot

13. After reboot, choose your flash drive to install Windows 10 at normally.

When install coming to the step like below illustration, click Load driver. 

※ Driver download link ==>https://download.biostar.com.tw/upload/Driver/Chipset/ATI/AM4_SATA/WIN10x64_F6.zip

( Unzip and copy the folder to your flash drive.)

14. Click Browse.

15. Choose the driver folder.

16. Uncheck "Hide drivers that aren't compatible with this  computer's hardware.

Choose all files and click "Next".

17. After driver loaded, the array will be detected.

1. Get to Biostar website :  https://www.biostar.com.tw/app/en/index.php

2. Search the model on the upper right corner.

Ex: X470GT8

3. Select "X470GT8"

4. Click Download.

5. Select the BIOS file to download.

6. Then you can download the BIOS file.

Note: You can to use "F12" update BIOS.

For OS windows 10, please follow the steps below.

1. Enter to the Windows 10.

2. Click the right button on the Windows start and select the Power Options.

.

3. Select Additional power settings.

4.Select Choose what the power buttons do.

5. Select Change settings that are currently unavailable.

6. Cancel the tick from the option Turn on fast startup then Save change

.

7. Please reboot the system.

8. After reboot, at the next system shutdown it won't have any power from USB ports.

1.Open the BIOScreen utility program.

2.Click Load image for input custom logo.

3.Choose LOGO.jpg file or .bmp file and utility will show preview on right side. Then click Open.

4. After load the LOGO, please click Transform button and wait for a moment for BIOS file transfer.

5. After transform Image finished, please press OK then click Update BIOS.

6. Click OK to update BIOS with custom logo.It will take a few minute for system to update BIOS. Do not turn off power or run other programs.

7. When update BIOS finish, please click OK and system will automatically restart.

8. You will see the custom logo on POST screen.

Note: 

1. The picture's file must be .jpg or .bmp.

2.  We recommend using a size image of size 800 x 600.

First, please double check your VGA card whether support UEFI mode or follow the steps as below :

1. Turn OFF your system.

2. Remove the VGA card, then conntect your monitor into onboard VGA or DVI port.

3. Power ON your system, then press [Delete] key into BIOS Setup Menu (CMOS).

4. Select the option as Boot > CSM Support > change the option from [Disabled] to [Enabled].

5. Press F10 to Save configuration and reset.

6. Turn OFF your system, then install the VGA card.

7. Please connect your monitor into VGA card, then Power ON your system.

And it will work.

1. Please try to download correct (lastest) BIOS file via your model's download page. 

2. Copy this BIOS file into a bootable USB flash drive as Root Path, then you will need to rename BIOS file as "AMIBOOT.ROM". More detail by refer to below.

3. Remove the CMOS battery, set the CMOS clear jumper to reset CMOS.

4. Wait for a while, then put back the battery, set the CMOS clear jumper to original state.

5. plug the USB flash drive into your system.

6. Power on System while pressing "Ctrl+Home" continuously.

7. After 30 seconds or more, it might be appear below Recovery screen.

After done,  you can reset the system and get POST display normally.

If the method can not help you,  we suggest you contact with local seller for future help.

Set TB350-BTC / TA320-BTC for mining

Please update BIOS.
(How to update BIOS by key "F12" :　http://www.biostar.com.tw/app/en/support/faq_content.php?S_ID=491) 
TB350-BTC => B35BG209.BSS 
TA320-BTC => A32BGB30.BSS
(TA320-BTC default setting already as same as below)

After update (For TB350-BTC), you have to manual set and check as below : 
1. Enable : Above 4G Decoding (BIOS / Advanced / PCI Subsystem settings / Above 4G Decoding  )
2. Enable : Mining Mode (BIOS / Chipset / Mining mode)
3. Disable : CSM Support (BIOS / Advanced / CSM Configuration / CSM Support) 

Set on-board primary display.(Only for Bristol and Raven CPU)

BIOS / Chipset / North Bridge / GFX Configuration / 
Primary Video Device => IGD Video
Surround View => Auto

Set PCIe Speed 

BIOS / Chipset / North Bridge / GFX Configuration / PPSP Policy

Performance => Gen3
Balanced High => Gen2
Balanced Low => Gen1 

• Hardware 
  Ensure hardware connect properly first.
  (1). Check VGA card 
  Try to only plug one VGA card in PEX16_1 (long yellow slot) directly without riser card => Check whether display
  
  (2). Check Riser card 
  Try to plug VGA card with only one riser card to test per PEX1 and PEX16_1 => Check whether display.
  
  (3). Check CPU socket Pin
  Remove CPU and check CPU Socket pin whether bent.(If bent , might be no power on or no display.
  
  (4). Check Riser Card and VGA card power are connected properly.
  
  (5). Refer Mining Guide to deploy Rig : http://www.biostar.com.tw/app/en/event/crypto_mining/page4_2.htm
  
   
• Under BIOS
  (1). Ensure BIOS up to latest.
  TB250-BTC => B25CFB29.BSS or latest
  TB250-BTC+ => B25EFB29.BSS or latest
  TB250-BTC Pro  => B25DB29.BSS or latest
  After update and get POST , BIOS will detect PCIE and show each slot status automatically.
  
  (2). Plug all VGA card in slot and into BIOS to check whether get (Present)
  PEX1_1-PEX1_11 => Chipset Menu /PCH-IO Configuration / PCI Express Configuration.
  PEX16_1 => Chipset Menu / System Agent(SA) Configuration
  
  (3). Check BIOS setting. (Or use BIOS default setting)
  Enable Mining mode (Chipset / Mining Mode)
  Enable Above 4G Decoding (Chipset / System Agent (SA) Configuration / Above 4G MMIO BIOS Assignment)
  Disable CSM Support (Boot / CSM support )
  =>Disable CSM support option , it will only recognize UEFI device.
   
• Under Windows
  ***Please make sure BIOS get all VGA card first.***
  (1). Check OS be installed by UEFI format (How to check install by UEFI)
  
  (2). Check Device Manager do not show yellow exclamation mark.
  
  (3). Check VGA card driver up to date.

1. Under Windows10 , press key "Windows" + "R" 
2. Key in msinfo32
   
3. System Information will show BIOS mode.