Biostar

1. Insert both of your memory in DIMMA2 and DIMMB2 (If you motherboard has 4 slots)

2. Power on and enter BIOS setup.

3. Make sure the BIOS version of your motherboard is up to date. (For example X370GT7)

4. Set the Memroy Clock Mode to XMP and press F10 to save & exit.

After system reboot, you will see system is running 3200(OC).

The model TB360-BTC Expert motherboard only allow you insert lower than 13pcs graphics card in motherboard.

However if you want to use more than 13pcs graphics card you have to use mining card instead.

For futher information about mining card please refer the following link.

--> https://www.techpowerup.com/gpu-specs/p106-100.c2980

In the INTEL 400 series, the Intel official statement does not provide V-BIOS Output for LEGACY mode.

If you wanna set the CSM to "Enabled" to work the VGA on LEGACY mode, please install an extra VGA card to output display.

1. Please press “Delete” when the system POST, to enter BIOS.

2. Press “F7” to go to advance model.

3. Go to Advance-> SATA And RST Configuration.

4. Set SATA Mode Selection to “Intel RST Premium With Optane System Acceleration”

5. Set PCIe Storage On M2M_32G_1 & PCIe Storage On M2M_32G_2 to “RST Controlled".

6. Press “F10” to Save & Exit

7. When the system boot on, go under BIOS-> advance ->Intel(R) Rapid Storage Technology.

8. Go to Create RAID Volume.

9. Set the RAID Level to “RAID0 (Stripe)” and change both of the Disk options to “X”.

10. Select Create Volume.

11. Then, enter the RAID Volume to check the details of RAID 0.

12. After checking, press “F10” again to Save & Exit.

13. When the system reboot automatically, press “F9” to select the bootable device and start the installation of OS.

1. Please press “Delete” when the system POST, to enter BIOS.

2. Press “F7” to go to advance model.

3. Go to Advance-> SATA And RST Configuration.

4. Set SATA Mode Selection to “Intel RST Premium With Optane System Acceleration”

5. Press “F10” to Save & Exit

6. When the system boot on, go under BIOS-> advance ->Intel(R) Rapid Storage Technology.

7. Go to Create RAID Volume.

8. Set the RAID Level to “RAID0 (Stripe)” and change both of the Disk options to “X”.

9. Select Create Volume.

10. Then, enter the RAID Volume to check the details of RAID 0.

11. After checking, press “F10” again to Save & Exit.

12. When the system reboot automatically, press “F9” to select the bootable device and start the installation of OS.

First of all, here are some tips that apply to all products:

• Use only a soft, lint-free cloth. Avoid abrasive cloths, towels, paper towels, or similar items. 
• Avoid excessive wiping, which might cause damage. 
• Unplug all external power sources, devices, and cables.
• Keep liquids away from the product.
• Don't get moisture into any openings.
• Don't use aerosol sprays, bleaches, or abrasives.
• Don't spray cleaners directly onto the item.

How to clean your computer:

First, shut down your PC and unplug the power cord along with other connected devices.

Next use a damp, soft, lint-free cloth to clean the computer's surface.

Avoid getting moisture in any openings. Don't spray liquid directly on the computer.

Don't use aerosol sprays, solvents, abrasives, or cleaners containing hydrogen peroxide and hypochlorous acid that might damage the product.

If you want to install Windows7 32Bit on H110M-BTC, please follow the steps below.

1. Boot up your system, press [DEL] go to BIOS.

2. BIOS -> Chipset -> Mining Mode -> [Disabled].

3. BIOS -> Boot -> CSM Support -> [Enabled].

4. Press [F10], save the modification and exit.

5. After system reboot, you should now be able to install Windows7 32Bit.

First of all, please make sure the graphics card which you use support AMD FreeSync.

Next, please get to AMD website and see the FreeSync monitors support list to choose your monitor.

--> https://www.amd.com/en/products/freesync-monitors

Here we use our VA5505RF41 graphics card with AOPEN 24HC1QR monitor.

After AMD driver installed, you can find the Radeon FreeSync option in the AMD Radeon settings. 

1. Power on, press [DEL] goto BIOS.

2. Advanced -> SATA Configuration -> OnChip SATA Type -> [RAID].

3. Advanced -> CSM Configuration -> Storage -> [UEFI].

4. Press [F10], save the changes and reboot.

5. After reboot, go to BIOS again, RAIDXpert2 Configuration Utility option will show at the bottom of Advanced page.

6. RAIDXpert2 Configuration Utility -> Physical Disk Management ->Select Physical Disk Operations -> Inlitialize Disk

Enabled the disk you want to make array and select [OK].

7. RAIDXpert2 Configuration Utility -> Array Management -> Create Array -> Select Physical Disks

Enabled the disks that you want to make array and select [Apply Changes]

8. After finished the settings, select [ Create Array ].

9. Array has been successfully set.

If you want to install On-Board VGA driver on B360MHD PRO2 with i5-9400 or i5-9600K CPU.

Please make sure your Windows 10 version is after 1703 version.

You can press [windows] + [R], key in winver to check it.

If your Windows 10 version is before 1703 version, please update it first.